LCD Display Module Blue Backlight for Arduino LCD1602 IIC I2C TWI 1602 Serial

PKR  1,050
It is another great blue backlight LCD display. As the pin resources of controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module,

PL2303 USB To RS232 TTL USB Converter Adapter Module For Arduino

PKR  180

Adopt imported controller RS232 TTL,which can stabilize the flash with high speed
500mA self recovery fuse for protection
Two data transmission indicator can monitor data transfer status in real time
Reserve 3.3V and 5V pin interface,easy for the DDWRT of different voltage system that need power
The entire board is coated by high quality transparent heat-shrinkable sleeve,making the PCB in insulation state from outside,

UNO Proto shield prototype expansion board SYB-170 mini board

PKR  250
Used in conjunction with the Duemilanove ProtoShield prototype expansion board, the circuit is used to build a prototype, can be directly soldered components on the board, you can also connect the above mini breadboard circuit. Bread board and circuit board via double-sided adhesive connections, sold bread board and the circuit board are separated. ProtoShield prototype expansion board with two buttons and two LED circuit can be used directly, all of the pins and the power leads are very fit and build circuit prototyping with Ardui-no.

USB to TTL UART module CH340G CH340 3-3V-5V switch

PKR  250

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Status LED. Dual 3.3V and 5V Power output, work with 3.3v and 5v target device

Water Level Sensor Module Detection Depth Height Arduino

PKR  50
Water Level Sensor
Condition: New
Operating voltage: DC3-5V
Operating current: less than 20mA
Sensor Type: Analog
Detection Area: 40mmx16mm
Production process: FR4 double-sided HASL
Operating temperature:10-30
Humidity: 10% -90% non-condensing

4-Phase Stepper Motor and Driver Board ULN2003 Module Arduino

PKR  350
5V 4-Phase Stepper Step Motor + Driver Board ULN2003 with drive Test Module Machinery Board for Arduino Diameter: 28mm / 1.1in Voltage: DC 5V Length: 274mm / 10.8in Step Angle: 5.625 * 1/64 Reduction ratio: 1/64 DC Resistance: 200±7% (25)

DC-DC LM2596 Step-down Adjustable Module CC-CV

PKR  350
Fixed turn the lamp current to 0.1 times the value of the constant current (charge when used to identify whether the battery is full); 2. Increased input reverse polarity protection diode; 3. Using dedicated reference IC, and high-precision sampling resistor, so that the constant current is more stable, (20 degrees to 100 degrees, the constant current 1A, when the temperature drift of less than 1%).Particularly suitable for LED driver *High-power LED constant current drive *Lithium battery charger (including ferroelectric)

Dual axis XY Joystick Module For Arduino projects

PKR  200
4 X 2.6 X 3.2CM
2 potentiometers for 2 axes
1 switch
Connector: +5Vcc - GND - VRx - VRy - SW
Package Included:
20 x XY Joystick Module

LCD Display Module Blue Backlight for Arduino LCD1602 IIC I2C TWI 1602 Serial

PKR  1,050
It is another great blue backlight LCD display. As the pin resources of controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module,

PL2303 USB To RS232 TTL USB Converter Adapter Module For Arduino

PKR  180

Adopt imported controller RS232 TTL,which can stabilize the flash with high speed
500mA self recovery fuse for protection
Two data transmission indicator can monitor data transfer status in real time
Reserve 3.3V and 5V pin interface,easy for the DDWRT of different voltage system that need power
The entire board is coated by high quality transparent heat-shrinkable sleeve,making the PCB in insulation state from outside,

UNO Proto shield prototype expansion board SYB-170 mini board

PKR  250
Used in conjunction with the Duemilanove ProtoShield prototype expansion board, the circuit is used to build a prototype, can be directly soldered components on the board, you can also connect the above mini breadboard circuit. Bread board and circuit board via double-sided adhesive connections, sold bread board and the circuit board are separated. ProtoShield prototype expansion board with two buttons and two LED circuit can be used directly, all of the pins and the power leads are very fit and build circuit prototyping with Ardui-no.

USB to TTL UART module CH340G CH340 3-3V-5V switch

PKR  250

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Status LED. Dual 3.3V and 5V Power output, work with 3.3v and 5v target device

Water Level Sensor Module Detection Depth Height Arduino

PKR  50
Water Level Sensor
Condition: New
Operating voltage: DC3-5V
Operating current: less than 20mA
Sensor Type: Analog
Detection Area: 40mmx16mm
Production process: FR4 double-sided HASL
Operating temperature:10-30
Humidity: 10% -90% non-condensing

4-Phase Stepper Motor and Driver Board ULN2003 Module Arduino

PKR  350
5V 4-Phase Stepper Step Motor + Driver Board ULN2003 with drive Test Module Machinery Board for Arduino Diameter: 28mm / 1.1in Voltage: DC 5V Length: 274mm / 10.8in Step Angle: 5.625 * 1/64 Reduction ratio: 1/64 DC Resistance: 200±7% (25)
GAMING COLLECTION

Sony Playstation 4 Dualshok Controller

INNOVATIVE GADGETS

OUR PARTNERS

Play Video