0.91 inch OLED display White 12832 IIC 128*32 LCD screen for arduino display device SSD1306
SKU:
1561
In stock
6 in 1 AC 100A Digital Voltmeter Ammeter Energy Power Frequency Factor Current Panel Meter Detector
SKU:
2168
In stock
Clear Acrylic Case Shell Housing For ESR SCR/MOS / LCR-T4 Transistor Tester
SKU:
1235
In stock
CP2102 WiFi Bluetooth 0.96 inch OLED ESP32 18650 Battery Development Board ESP8266
SKU:
2089
In stock
18650 charging system integrated.
indicate LED inside(Green means full& Red means charging)
Charging and working could be at the same time.
1 Switch could control the power.
1 extra LED could be programmed(Connected with GPIO16[D0])
0.5A charging current
1A output
Over charge protection
Over discharge protection
Full ESP32 pins break out
DC 100V 50A Red Blue Digital Voltmeter Ammeter 2 in1 DC Volt Amp Meter With Shunt
SKU:
1746
In stock
Operating voltage:DC 4 ~ 30V
Measure voltage: DC 0 ~ 100V
Minimum resolution(V): 0.1V
Measure current :50A (require external shunt)
Minimum resolution(A): 0.1A
Operating current: <20mA
Display: three 0.28" LED digital tube
Display color: Red and Blue (two-color display)
Refresh rate: about 300mS / times
Measure accuracy: 1% (± 1 digit)
Operating temperature: -10 to 65° c
Operating Humidity: 10 to 80% (non-condensing)
Working pressure: 80 to 106 kPa
Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement
Dual USB Current Voltage Charger Detector battery Tester Voltmeter Ammeter
SKU:
1157
In stock
Compact and easy to carry, no additional power supply, plug and play.
It can easily measure the output voltage of the USB port and the device operating current or load voltage
Detect any USB charger such as PC USB, home charger, car charger.
Wide range of applications, any phone, any electronic product, Easy to use.
Suitable for factories, laboratories and personal use.
Voltage range: 3.3V-18V
Current range: 0-3A
Voltage display: red
Current display: blue
Size: 52mm x 34mm x12mm
Weight: 16g
Flysky FS-i6 FS I6 2.4G 6ch RC Transmitter with Receiver For RC Helicopter Plane Quadcopter Glider
SKU:
1304
In stock
RF specification:
RF Range: 2.405 - 2.475GHz
Bandwidth: 500khz
RF Power: less than 20dBm
RF mode: AFHDS 2A
Modulation type: GFSK
RX Sensibility: -105dBm
Receiver specification:
Channel: 6
Model type: fixed wing/helicopter/glider
RF receiver sensitivity: -105dBm
Modulation: GFSK
System type: AFHDS2A/AFHDS
Channel resolution: 1024 steps
Bind port: yes
Power port: yes( VCC)
Power: 4V -6.5V DC
Weight: 6.4g
Antenna lenght: 26mm
Size: 40.4 x 21.1 x 7.35 mm
MP3 module/Card speakers USB MP3 decoding module PCBA board JLH-68016H
SKU:
1951
In stock
OLED Display Module 12864 0.96 Inch 4Pin yellow/ Blue IIC I2C LED For Arduino
SKU:
1934
In stock
The instructions on four needles IIC interface module
Four needles iic interface is relatively simple, only two signal lines
1. The GND power to
2. The VCC power supply is (3 ~ 5.5 V)
3. The SCL OLED D0 feet, for the clock pin in the IIC communication
4. The SDA OLED D1 feet, in the IIC communication pin for the data
QC2.0 QC3.0 Automatic USB Trigger Tester Voltage Ammeter Quick Charger Power Bank Voltage
SKU:
2350
In stock
USB female port output.
QC 2.0 5V/9V/12V trigger voltage.
Supports Manual mode and Auto mode.
Manual mode: Short press for trigger voltage switch.
Auto mode: Long press enter auto mode, trigger voltage will repeat in the sequence of 5V to 9V to 12V.
For test charger and power bank that support QC2.0 output.
Square LED 8X8 Common Dots Matrix Module Arduino
SKU:
1025
In stock
TFT LCD 3.2 inch Mega Touch Expansion Board Shield for Arduino
SKU:
1400
In stock
TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board that use TFT01 LCD module.
TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist.
