Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique.
• UL,CUL,TUV recognized.
• Selection of plastic material for high temperature and better chemical solution performance.
• Sealed types available.
• Simple relay magnetic circuit to meet low cost of mass production.
5 Colors 5mm F5 Ultra Bright Round LED Diode Kit Red / Green / Blue / White / Yellow
Working current: 20 (mA)
Working voltage: Red: 1.9V-2.1V
Yellow: 1.9V-2.1V
Blue:3.0V-3.2V
Green: 3.0V-3.2V
White:3.0V-3.2V
DIY mobile power, car power, communications equipment and power supply.
Technical Parameters:
Module Properties: Non-isolated step-down module (BUCK)
Rectification: Non-synchronous rectifier
Input voltage: DC 5V-30V
Output voltage: DC 0.8V-24V (Adjustable, Output < Input)
Output current:Rated current is 2.5A,(5A Max, If current is larger than 2.5A, eEnhancement of heat dissipation is required.)
Continuous Drain Current, VGS @ 10V = 110 A
Pulsed Drain Current = 390 A
At 25°C Power Dissipation = 200 W
Linear Derating Factor = 1.3 W/°C
Gate-to-Source Voltage = ± 20 V
Avalanche Current = 62 A
Repetitive Avalanche Energy = 20 mJ
dv/dt Peak Diode Recovery dv/dt = 5.0 V/ns
Operating Junction and Soldering Temperature, for 10 seconds = 300 (1.6mm from case )°C
Conversion efficiency: Up to 92% (output voltage higher, the higher the efficiency)
Switching Frequency: 150KHz
Rectifier: Non-Synchronous Rectification
Module Properties: Non-isolated step-down module (buck)
Short circuit protection: current limiting, since the recovery
Operating temperature: Industrial grade (-40 to +85 ) (output power 10W or less)
Full load temperature rise: 40
Fixed turn the lamp current to 0.1 times the value of the constant current (charge when used to identify whether the battery is full);
2. Increased input reverse polarity protection diode;
3. Using dedicated reference IC, and high-precision sampling resistor, so that the constant current is more stable, (20 degrees to 100 degrees, the constant current 1A, when the temperature drift of less than 1%).Particularly suitable for LED driver
*High-power LED constant current drive
*Lithium battery charger (including ferroelectric)
Note:Output voltage must be higher than Input Voltage
Input Voltage:2-6V(less than 3V,output power cut down)
Output Voltage:3.3V-9V adjustable(Input voltage must less than output voltage)
Output Current:Rated 2000mA (2.8V-3V input, 5V output, 1500MA output,(single lithium battery higher 2600MAH input,5V output, output current can up to 2000MA)
Note:Output voltage higher than 6V,Please connect power first,then connect load line
MT3608 DC-DC Adjustable Boost Module 2A Step Up Module with MICRO USB 2V - 24V to 5V - 28V MT3608 LM2577
1. The maximum output current: 2A
2. The input voltage: 2V and 24V
3. The maximum output voltage: > 5V - 28V
4. Efficiency: > 93%
This module is based on a touch detection IC (TTP223B) of Capacitive type touch jog switch module . This module default output low, the low-power mode to mode; when a finger touching the corresponding position, the module will output high and returns low again touch. Mode is switched to fast mode; when for 12 seconds without touching
1. The XL6019 5A DC-DC Step Up Boost Converter Uses conventional BOOST complete constant voltage output scheme, internal integration of MOSFET, less peripheral devices, low system cost;
2. Wide voltage range input, input voltage up to 35V;the output voltage can be adjusted, and the maximum can be supported by 40V.
3. Built in over temperature protection, over-current protection full set of reliability and protection circuit, high reliability.
4. The system conversion efficiency can reach more than 90%, which is convenient for thermal design.
5. TO263-5L standard package, suitable for boosting applications within 30W.
Specification:
– Material: PCB Board
– Size: 5cm/1.97inch
Universal SetTop Box Power Supply Circuit Board SMPS for Free to Air D2H, DTH, Tata Sky, Set Top Box, Satellite Receiver Etc. Output : DC voltage via 4 pin header(+33V, Gnd, +12V, +24V, Gnd, +5V), SMPS
Length [ l ]: 16.2 mm
Pitch: 5.08 mm (0.200")
Width [ w ]: 15.2 mm
Constructional height: 12.92 mm
Height [ h ]: 16.22 mm
Pin dimensions 0,5 x 1 mm
Pin spacing: 10.16 mm
Wire Termination: Screw-less - Spring Cage, Tension Clamp
Mounting Type: Through Hole
Features: Lever Actuated
Hole diameter: 1.3 mm
Nominal current IN: 12 A
Maximum load current: 12 A (with 1.5 mm² conductor cross section)
Insulating material: PA
Flammability rating according to UL 94: V0
Stripping length: 10 mm
L9110 motor control chip
Module can be driven by two dc motors at the same time or one phase 4 line 2type stepping motor
Input voltage: 2.5-12V DC
Each channel has a continuous output current 800 ma
PCB Size: 29.2mm x 23mm
Type Designator: IRFB4110
Type of Transistor: MOSFET
Type of Control Channel: N -Channel
Maximum Power Dissipation (Pd): 370 W
Maximum Drain-Source Voltage |Vds|: 100 V
Maximum Gate-Source Voltage |Vgs|: 20 V
Maximum Gate-Threshold Voltage |Vgs(th)|: 4 V
Maximum Drain Current |Id|: 180 A
Maximum Junction Temperature (Tj): 175 °C
Reviews
There are no reviews yet.