4-Phase Stepper Motor and Driver Board ULN2003 Module Arduino buy in Pakistan
PKR 350
5V 4-Phase Stepper Step Motor + Driver Board ULN2003 with drive Test Module Machinery Board for Arduino
Diameter: 28mm / 1.1in
Voltage: DC 5V
Length: 274mm / 10.8in
Step Angle: 5.625 * 1/64
Reduction ratio: 1/64
DC Resistance: 200±7% (25)
In stock
Weight | 0.2 kg |
---|
Related Products
5V 4-Phase Stepper Step Motor + Driver Board ULN2003 with drive Test Module Machinery Board for Arduino
Specifications:
Diameter: 28mm / 1.1in
Voltage: DC 5V
Length: 274mm / 10.8in
Step Angle: 5.625 * 1/64
Reduction ratio: 1/64
DC Resistance: 200±7% (25)
Insulation Resistance: >10M (500V)
Dielectric Strength: 600V AC / 1mA / 1s
Insulation Grade: A
No-load Pull in Frequency: >600Hz
No-load Pull out Frequency: >1000Hz
Pull in Torque: >34.3mN.m(120Hz)
Detent Torque: >34.3mN.m
Related
Weight | 0.2 kg |
---|
Only logged in customers who have purchased this product may leave a review.
Related Products
PAM8403 mini 5V digital amplifier board with switch potentiometer
MB102 Breadboard Power Supply Module 3.3V 5V Bread Board
TTP223 Touch Switch Button Module Single Channel Self Locking
CMOS CAMERA OV7670 300KP VGA Camera Module
Soil moisture sensor Soil Hygrometer Humidity Detection module
Stepper Driver A4988 Module with Heat sink
433mhz rf wireless receiver transmitter module kit
L293D Motor Drive Shield for Arduino
XM1584 MP1584EN Ultra-small size DC-DC step-down module 3A adjustable super LM2596
DC-DC LM2596 Step-down Adjustable Module CC-CV
2 CHANNEL 5v RELAY Module 2-channel
Related Products
XL6019 5A DC-DC Step Up Boost Converter
XL4015 5A CC CV Adjustable Buck Converter
Universal Box Power Supply Circuit Board SMPS for Satellite Receiver 4 pin
PCB TERMINAL BLOCK 3 POLES SCREW LESS
L9110 Dual Channel DC Motor Driver H bridge Controller Board
IRFB4110 N-CHANNEL TRANSISTOR 100V 120A
FC-33 10mm Arduino RPM Sensor Rotational Speed Measuring Sensor
- Using imported groove optical coupling sensor, width 5mm.
- It have the output state light, if output high level, the lights are off. if output low level ,it on.
- If it covered,it will output high level;otherwise it output low level.
- Good signal and waveform, with strong driving ability for more than 15mA.
- The working voltage of 3.3V to 5V.
- Output: digital switch output (0 and 1).
- Equipped with a fixed bolt hole, easily install.
- Small board PCB size: 3.2 cm x 1.4 cm.
- Use the LM393 wide voltage comparer.
1200w 20A Dc Boost Step-up Converter
Specification
- Module name: 1200W boost constant current module
- Module properties: non isolated boost module (BOOST)
- Input voltage: 10-60V
- Input current: 20A
- Quiescent operating current: 15mA
- Output voltage: 12-83V continuous adjustable
- Output current: MAX 12A over 20A, please strengthen the
- cooling (with input and output differential pressure, the greater
- the pressure difference between the output current is small)
- Constant current range: 0.3-20A
- Output power: = input voltage x 10A
- Working temperature: -40~+85 degrees
- Working frequency: 150KHz
- Conversion efficiency: ≤95% (efficiency and input, output voltage,
- current, pressure difference)
- Installation: 4pcs 3mm column
- Connection mode: welding output (please use big current and pure copper wire)
- Module size: 130mmx52mmx46mm(LxWxH)
Reviews
There are no reviews yet.