Bluetooth audio receiver template stereo wireless speaker power amplifier DIY module 4.0 buy in Pakistan
PKR 270
Bluetooth audio receiver template, stereo wireless speaker, power amplifier modified DIY Bluetooth module 4.0
Module stereo output, built-in Bluetooth antenna structure is simple, the power supply voltage is 3.7V~5V version selection, active speakers increase Bluetooth connection function. 7PIN output interface is spacing 2.54 through hole, 7PIN output interface is: + power, ground, left channel, right channel, mute, LED status indicator, reserved port. The LED state port is connected with a 100 ohm resistor in series, LED indicates the ground connection, the Bluetooth is not connected and the flash is fast. After the Bluetooth connection is successful, it is slow flashing. The volume is 30mm X 20mm X 3mm
In stock
Weight | 0.003 kg |
---|
Related Products
Bluetooth audio receiver template, stereo wireless speaker, power amplifier modified DIY Bluetooth module 4.0
Module stereo output, built-in Bluetooth antenna structure is simple, the power supply voltage is 3.7V~5V version selection, active speakers increase Bluetooth connection function. 7PIN output interface is spacing 2.54 through hole, 7PIN output interface is: + power, ground, left channel, right channel, mute, LED status indicator, reserved port. The LED state port is connected with a 100 ohm resistor in series, LED indicates the ground connection, the Bluetooth is not connected and the flash is fast. After the Bluetooth connection is successful, it is slow flashing. The volume is 30mm X 20mm X 3mm.
Package Included:
Bluetooth motherboard 1 blocks
Electrolytic capacitors 2
LED 2
Resistance 1
Related
Weight | 0.003 kg |
---|
Only logged in customers who have purchased this product may leave a review.
Related Products
5V 9V 12V 10A PWM DC Motor Speed Controller LED Dimmer Module Adjustable Speed Regulator
Mosfet IRF3205 IRF3205PBF IR TO-220 55V 110A 200W
MB102 Breadboard Power Supply Module 3.3V 5V Bread Board
DC-DC LM2596 Step-down Adjustable Module CC-CV
12V 8A Switch Dimmer Brightness Adjustable Controller for DC motor LED Strip Light
MT3608 DC-DC Adjustable Step Up Boost Module 2A with MICRO USB LM2577
PAM8403 mini 5V digital amplifier board with switch potentiometer
MICRO USB to DIP Adapter 5pin Female Connector B Type PCB Converter
SN74HC595N 74HC595N 74HC595 DIP-16 SHIFT REGISTER IC
LM2596 DC Adjustable Step-Down 3A Power Supply Module
Stepper Driver A4988 Module with Heat sink
Related Products
XL6019 5A DC-DC Step Up Boost Converter
XL4015 5A CC CV Adjustable Buck Converter
Universal Box Power Supply Circuit Board SMPS for Satellite Receiver 4 pin
PCB TERMINAL BLOCK 3 POLES SCREW LESS
L9110 Dual Channel DC Motor Driver H bridge Controller Board
IRFB4110 N-CHANNEL TRANSISTOR 100V 120A
FC-33 10mm Arduino RPM Sensor Rotational Speed Measuring Sensor
- Using imported groove optical coupling sensor, width 5mm.
- It have the output state light, if output high level, the lights are off. if output low level ,it on.
- If it covered,it will output high level;otherwise it output low level.
- Good signal and waveform, with strong driving ability for more than 15mA.
- The working voltage of 3.3V to 5V.
- Output: digital switch output (0 and 1).
- Equipped with a fixed bolt hole, easily install.
- Small board PCB size: 3.2 cm x 1.4 cm.
- Use the LM393 wide voltage comparer.
1200w 20A Dc Boost Step-up Converter
Specification
- Module name: 1200W boost constant current module
- Module properties: non isolated boost module (BOOST)
- Input voltage: 10-60V
- Input current: 20A
- Quiescent operating current: 15mA
- Output voltage: 12-83V continuous adjustable
- Output current: MAX 12A over 20A, please strengthen the
- cooling (with input and output differential pressure, the greater
- the pressure difference between the output current is small)
- Constant current range: 0.3-20A
- Output power: = input voltage x 10A
- Working temperature: -40~+85 degrees
- Working frequency: 150KHz
- Conversion efficiency: ≤95% (efficiency and input, output voltage,
- current, pressure difference)
- Installation: 4pcs 3mm column
- Connection mode: welding output (please use big current and pure copper wire)
- Module size: 130mmx52mmx46mm(LxWxH)
Reviews
There are no reviews yet.