SI2301DS SOT23-3 SI2301 A1SHB SOT23-3 SMD transistor buy in Pakistan
PKR 8
1. VDS = -20V,ID =-2.5A
(1) RDS(ON) < 160m? @ VGS =-4.5V
(2) RDS(ON) < 230m? @ VGS =-2.5V
2. High Power and current handing capability
3. Lead free product is acquired
4. Surface Mount Package
Application
1. Battery protection
2. Load switch
3. Power management
Maximum ratings
1. Drain-Source Voltage : VDS = -20
2. Gate-Source Voltage : VGS = ?8V
3. Continuous Drain Current : ID = -2.3
4. Maximum Power Dissipation : PD = 0.35 W
1. VDS = -20V,ID =-2.5A (1) RDS(ON) < 160mΩ @ VGS =-4.5V (2) RDS(ON) < 230mΩ @ VGS =-2.5V 2. High Power and current handing capability 3. Lead free product is acquired 4. Surface Mount Package
Application
1. Battery protection 2. Load switch 3. Power management
Maximum ratings
1. Drain-Source Voltage : VDS = -20 2. Gate-Source Voltage : VGS = ±8V 3. Continuous Drain Current : ID = -2.3 4. Maximum Power Dissipation : PD = 0.35 W
MT3608 DC-DC Adjustable Boost Module 2A Step Up Module with MICRO USB 2V - 24V to 5V - 28V MT3608 LM2577
1. The maximum output current: 2A
2. The input voltage: 2V and 24V
3. The maximum output voltage: > 5V - 28V
4. Efficiency: > 93%
Brand new & high quality
Breadboard power supply module, compatible with 5 V, 3.3 V
Apply to MB102 breadboard
Input voltage: 6.5-12 V (DC) or USB power supply
Output voltage: 3.3V/5V can switch over
Maximum output current: <700 ma
Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V
Fixed turn the lamp current to 0.1 times the value of the constant current (charge when used to identify whether the battery is full);
2. Increased input reverse polarity protection diode;
3. Using dedicated reference IC, and high-precision sampling resistor, so that the constant current is more stable, (20 degrees to 100 degrees, the constant current 1A, when the temperature drift of less than 1%).Particularly suitable for LED driver
*High-power LED constant current drive
*Lithium battery charger (including ferroelectric)
MICRO USB is an international standard, most smartphone data lines have adopted this interface,
wide range of uses, this module easily be converted to conventional DIP2.54mm pin,
a great convenience to your application!
Max voltage: 16V
Minimum voltage: 5V
Continuous current: 10A
Short maximum current: 20A (less than 10 seconds)
Speed control mode: PWM step-less speed regulation, can also be used to adjust the light
Control mode: speed control potentiometer (clockwise clicked open, continue to rotate clockwise from 1% to 99% speed)
Duty cycle: 0%-99% (0% position is the state of the switch off when the potentiometer is most on the left).
When the current is switched on, the 0.002A (long time no need to switch off the governor is no current).
Efficiency: the maximum efficiency is as high as 98%.
Volume: long 3cm (excluding potentiometer), width 2cm, height 1.4cm
DIY mobile power, car power, communications equipment and power supply.
Technical Parameters:
Module Properties: Non-isolated step-down module (BUCK)
Rectification: Non-synchronous rectifier
Input voltage: DC 5V-30V
Output voltage: DC 0.8V-24V (Adjustable, Output < Input)
Output current:Rated current is 2.5A,(5A Max, If current is larger than 2.5A, eEnhancement of heat dissipation is required.)
The RF receiver modules are widely used for data receiving and signal control. They are specified as preferred components in remote control garage, roller curtain, door locks, remote sensing, telemetry, industrial control and wireless security alarm industry.
This module is based on a touch detection IC (TTP223B) of Capacitive type touch jog switch module . This module default output low, the low-power mode to mode; when a finger touching the corresponding position, the module will output high and returns low again touch. Mode is switched to fast mode; when for 12 seconds without touching
SS8050 SOT23-3 y2 smd TRANSISTOR 40v 1.5A (PNP) original JSCJ product
Polarity: PNP
Maximum Collector Power Dissipation (Pc): 0.225 W
Maximum Collector-Base Voltage |Vcb|: 40 V
Maximum Collector-Emitter Voltage |Vce|: 25 V
Maximum Emitter-Base Voltage |Veb|: 5 V
Maximum Collector Current |Ic max|: 1.5 A
Max. Operating Junction Temperature (Tj): 150 °C
Forward Current Transfer Ratio (hFE), MIN: 200
S8050 SOT23-3 j3y TRANSISTOR (NPN)
FEATURES
Complimentary to S8550
Collector Current: IC=0.5A
MARKING: J3Y
MAXIMUM RATINGS (Ta=25℃ unless otherwise noted)
Symbol Parameter Value Unit
VCBO Collector-Base Voltage 40 V
VCEO Collector-Emitter Voltage 25 V
VEBO Emitter-Base Voltage 5 V
IC Collector Current -Continuous 0.5 A
Reviews
There are no reviews yet.