USB ISP Programmer for ATMEL AVR ATMega ATTiny Board buy in Pakistan
PKR 600
Features:
-This device connects to your computer’s USB port. Not only is it quite compact, but the design is really elegent. The USB interface is achieved by using an atmega processor and the rest is done in firmware.
-With 500mA over-current protection self-recovery fuse, and complete protection of expensive computer motherboard designed for notebook computers, special two 3.6V regulator, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings. —–The well-configured firmware, the speed of the unique adaptive technology, stability and obtain the best balance between speed! Supports firmware upgrade unlimited
This device connects to your computer’s USB port. Not only is it quite compact, but the design is really elegent. The USB interface is achieved by using an atmega processor and the rest is done in firmware
With 500mA over-current protection self-recovery fuse, and complete protection of expensive computer motherboard
designed for notebook computers, special two 3.6V regulator, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings
The well-configured firmware, the speed of the unique adaptive technology, stability and obtain the best balance between speed! Supports firmware upgrade unlimited
The 74HC595; 74HCT595 is an 8-bit serial-in/serial or parallel-out shift register with a storage register and 3-state outputs. Both the shift and storage register have separate clocks. The device features a serial input
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
Note:Output voltage must be higher than Input Voltage
Input Voltage:2-6V(less than 3V,output power cut down)
Output Voltage:3.3V-9V adjustable(Input voltage must less than output voltage)
Output Current:Rated 2000mA (2.8V-3V input, 5V output, 1500MA output,(single lithium battery higher 2600MAH input,5V output, output current can up to 2000MA)
Note:Output voltage higher than 6V,Please connect power first,then connect load line
The RF receiver modules are widely used for data receiving and signal control. They are specified as preferred components in remote control garage, roller curtain, door locks, remote sensing, telemetry, industrial control and wireless security alarm industry.
Motor Drive Shield L293D for Arduino Duemilanove Mega / UNO
4-channel DC motor drives, stepper motor or 2 while driving two servos, You can mix:
DC motor driver quad and two steering gear
Drive two DC motor and stepper motor all the way and two-way steering gear
Drive two stepper motors and two servos
Universal SetTop Box Power Supply Circuit Board SMPS for Free to Air D2H, DTH, Tata Sky, Set Top Box, Satellite Receiver Etc. Output : DC voltage via 4 pin header(+33V, Gnd, +12V, +24V, Gnd, +5V), SMPS
This is a common 555 timer IC. A classic for all of those first-year circuits projects where you need to blink an LED, generate tone, and thousands of other great beginning projects. Google around for a huge list of resources and example projects.
L9110 motor control chip
Module can be driven by two dc motors at the same time or one phase 4 line 2type stepping motor
Input voltage: 2.5-12V DC
Each channel has a continuous output current 800 ma
PCB Size: 29.2mm x 23mm
Type Designator: IRFB4110
Type of Transistor: MOSFET
Type of Control Channel: N -Channel
Maximum Power Dissipation (Pd): 370 W
Maximum Drain-Source Voltage |Vds|: 100 V
Maximum Gate-Source Voltage |Vgs|: 20 V
Maximum Gate-Threshold Voltage |Vgs(th)|: 4 V
Maximum Drain Current |Id|: 180 A
Maximum Junction Temperature (Tj): 175 °C
1. High Efficiency Synchronous Rectification in SMPS
2. Uninterruptible Power Supply
3. High Speed Power Switching
4. Hard Switched and High Frequency Circuits
UTC D313 NPN EPITAXIAL PLANAR TRANSISTOR NPN EPITAXIAL PLANAR TRANSISTOR
The UTC D313 is designed for use in general purpose amplifier and switching applications.
1 TO-220
1:BASE
2:COLLECTOR
3:EMITTER ABSOLUTE MAXIMUM RATINGS PARAMETER Collector-Base Voltage Collector-Emitter Voltage Emitter-Base Voltage Collector Current Storage Temperature Junction Temperature SYMBOL VCBO VCEO VEBO Ic TSTG Tj VALUE 60 60 5 3 -55 ~ +150 150 UNIT V V V A °C °C ELECTRICAL CHARACTERISTICS(Ta=25°C) PARAMETER Collector-Base Breakdown Voltage Collector-Emitter Breakdown Voltage Emitter-Base
Reviews
There are no reviews yet.