Click to enlarge

18650 battery holder 5X3 bracket spacer Cell cylindrical in Pakistan

PKR  100

55 Products Sold in last 30 days


Last updated: 15 September, 2024
x

کسٹمر کو رقم ادائیگی سے پہلے پارسل کھولنے کی اجازت ہے

SKU: 3094 Category:

5×3 Battery Cell Spacer Radiating Shell Plastic Holder Bracket 18650 Cell
18650 3?5 Battery Cell Spacer/Holder is a cylindrical battery spacer, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance

Related products

12V 8A Switch Dimmer Brightness Adjustable Controller for DC motor LED Strip Light

, , ,
SKU: 1189

In stock

PKR  540
Adjust the light soft and stable, no flickering PWM digital dimming, avoid rush current, protect your LED lights Mainly use to adjust single color LED light lamps and Led Strip
Add to wishlist
Add to cart
Quick view

3V to 5V to 9V 2A USB Output Voltage Step-up Module Boost Converter

, , ,
SKU: 1177

In stock

PKR  300
Note:Output voltage must be higher than Input Voltage Input Voltage:2-6V(less than 3V,output power cut down) Output Voltage:3.3V-9V adjustable(Input voltage must less than output voltage) Output Current:Rated 2000mA (2.8V-3V input, 5V output, 1500MA output,(single lithium battery higher 2600MAH input,5V output, output current can up to 2000MA) Note:Output voltage higher than 6V,Please connect power first,then connect load line
Add to wishlist
Add to cart
Quick view

4-Phase Stepper Motor and Driver Board ULN2003 Module Arduino

,
SKU: 1018

In stock

PKR  350
5V 4-Phase Stepper Step Motor + Driver Board ULN2003 with drive Test Module Machinery Board for Arduino Diameter: 28mm / 1.1in Voltage: DC 5V Length: 274mm / 10.8in Step Angle: 5.625 * 1/64 Reduction ratio: 1/64 DC Resistance: 200±7% (25)
Add to wishlist
Add to cart
Quick view

5A XL4015 DC-DC DSN5000 Adjustable Step Down Module with heat sink

, , ,
SKU: 1178

In stock

PKR  350
DIY mobile power, car power, communications equipment and power supply. Technical Parameters: Module Properties: Non-isolated step-down module (BUCK) Rectification: Non-synchronous rectifier Input voltage: DC 5V-30V Output voltage: DC 0.8V-24V (Adjustable, Output < Input) Output current:Rated current is 2.5A,(5A Max, If current is larger than 2.5A, eEnhancement of heat dissipation is required.)
Add to wishlist
Add to cart
Quick view

CMOS CAMERA OV7670 300KP VGA Camera Module

,
SKU: 1047

In stock

PKR  580
High sensitivity for low-light applications
Low voltage suitable for embedded applications
Standard SCCB interface compatible with I2C interface
RawRGB to RGB (GRB4: 2:2, RGB565/555/444), YUV (4:2:2) and YCbCr (4:2:2)output format
support VGA, CIF, and from CIF to 40x30 the size
Add to wishlist
Add to cart
Quick view

ESP8266 esp-01 remote serial Port WIFI wireless module D185

, ,
SKU: 1124

In stock

PKR  340
802.11 b/g/n Wi-Fi Direct (P2P), soft-AP Integrated TCP/IP protocol stack Integrated TR switch, balun, LNA, power amplifier and matching network Integrated PLLs, regulators, DCXO and power management units +19.5dBm output power in 802.11b mode Power down leakage current of <10uA Integrated low power 32-bit CPU could be used as application processor
Add to wishlist
Add to cart
Quick view

HC-05 HC05 Bluetooth JY-MCU 6 Pin Module

,
SKU: 1069

In stock

PKR  750
Serial port Bluetooth, Drop-in replacement for wired serial connections, transparent usage. You can use it simply for a serial port replacement to establish connection between MCU and GPS, PC to your embedded project and etc.

HC-06 has be
Add to wishlist
Add to cart
Quick view

HX711 Weighing & Pressure Sensor 24-bit Precision A/D Module

, ,
SKU: 1224

In stock

PKR  250
Two selectable differential input channels. There is no programming needed for the internal registers. All controls to the HX711 are through the pins. Simultaneous 50 and 60Hz supply rejection. Current consumption including on-chip analog power supply regulator: normal operation < 1.5mA, power down < 1uA. Operation supply voltage range: 2.6 ~ 5.5V. Operation temperature range: -40 ~ +85℃.
Add to wishlist
Add to cart
Quick view
Description

5×3 Battery Cell Spacer Radiating Shell Plastic Holder Bracket 18650 Cell
18650 3?5 Battery Cell Spacer/Holder is a cylindrical battery spacer, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance.

There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack.

This Battery Holder is compatible with our 18650 battery which you need to buy separately

Package Contains:
1PC 18650 battery holder 5X3 bracket spacer Cell cylindrical

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “18650 battery holder 5X3 bracket spacer Cell cylindrical”

Your email address will not be published. Required fields are marked *

You have to be logged in to be able to add photos to your review.

5×3 Battery Cell Spacer Radiating Shell Plastic Holder Bracket 18650 Cell
18650 3?5 Battery Cell Spacer/Holder is a cylindrical battery spacer, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance.

There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack.

This Battery Holder is compatible with our 18650 battery which you need to buy separately

Package Contains:
1PC 18650 battery holder 5X3 bracket spacer Cell cylindrical