Click to enlarge

WeMos D1 mini ESP8266 NodeMcu 4M bytes Lua WIFI module in Pakistan

PKR  550

Out of stock

کسٹمر کو رقم ادائیگی سے پہلے پارسل کھولنے کی اجازت ہے

SKU: 1329 Category: Tags: , , ,

D1 mini – Mini NodeMcu 4M bytes Lua WIFI Internet of Things development board based ESP8266 by WeMos

Related products

220V to 5V 3A 15W AC/DC Universal Regulated Switching Power Supply

, , ,
SKU: 1179

In stock

PKR  780
Input voltage : 110~220V AC Output Voltage: 5V DC Output Current: 3A Output Power:15W
Add to wishlist
Add to cart
Quick view

3V to 5V to 9V 2A USB Output Voltage Step-up Module Boost Converter

, , ,
SKU: 1177

In stock

PKR  300
Note:Output voltage must be higher than Input Voltage Input Voltage:2-6V(less than 3V,output power cut down) Output Voltage:3.3V-9V adjustable(Input voltage must less than output voltage) Output Current:Rated 2000mA (2.8V-3V input, 5V output, 1500MA output,(single lithium battery higher 2600MAH input,5V output, output current can up to 2000MA) Note:Output voltage higher than 6V,Please connect power first,then connect load line
Add to wishlist
Add to cart
Quick view

5A XL4015 DC-DC DSN5000 Adjustable Step Down Module with heat sink

, , ,
SKU: 1178

In stock

PKR  350
DIY mobile power, car power, communications equipment and power supply. Technical Parameters: Module Properties: Non-isolated step-down module (BUCK) Rectification: Non-synchronous rectifier Input voltage: DC 5V-30V Output voltage: DC 0.8V-24V (Adjustable, Output < Input) Output current:Rated current is 2.5A,(5A Max, If current is larger than 2.5A, eEnhancement of heat dissipation is required.)
Add to wishlist
Add to cart
Quick view

Dual axis XY Joystick Module For Arduino projects

,
SKU: 1024

In stock

PKR  200
4 X 2.6 X 3.2CM
2 potentiometers for 2 axes
1 switch
Connector: +5Vcc - GND - VRx - VRy - SW
Package Included:
20 x XY Joystick Module
Add to wishlist
Add to cart
Quick view

HX711 Weighing & Pressure Sensor 24-bit Precision A/D Module

, ,
SKU: 1224

In stock

PKR  250
Two selectable differential input channels. There is no programming needed for the internal registers. All controls to the HX711 are through the pins. Simultaneous 50 and 60Hz supply rejection. Current consumption including on-chip analog power supply regulator: normal operation < 1.5mA, power down < 1uA. Operation supply voltage range: 2.6 ~ 5.5V. Operation temperature range: -40 ~ +85℃.
Add to wishlist
Add to cart
Quick view

MB102 Breadboard Power Supply Module 3.3V 5V Bread Board

, ,
SKU: 1058

In stock

PKR  180
Brand new & high quality Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V
Add to wishlist
Add to cart
Quick view

PL2303 USB To RS232 TTL USB Converter Adapter Module For Arduino

, ,
SKU: 1012

In stock

PKR  180

Adopt imported controller RS232 TTL,which can stabilize the flash with high speed
500mA self recovery fuse for protection
Two data transmission indicator can monitor data transfer status in real time
Reserve 3.3V and 5V pin interface,easy for the DDWRT of different voltage system that need power
The entire board is coated by high quality transparent heat-shrinkable sleeve,making the PCB in insulation state from outside,
Add to wishlist
Add to cart
Quick view

USB to TTL UART module CH340G CH340 3-3V-5V switch

, ,
SKU: 1014

In stock

PKR  250

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Status LED. Dual 3.3V and 5V Power output, work with 3.3v and 5v target device

Add to wishlist
Add to cart
Quick view
Description

WeMos D1 mini – Mini NodeMcu 4M bytes Lua WIFI Internet of Things development board based ESP8266 by WeMos

Detials:

11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
   1 analog input(3.3V max input)
   a Micro USB connection
 
Package Included:
  1×WeMos D1 mini
   2×Long female pins
   2×Short female pins
   2×Normal pins
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “WeMos D1 mini ESP8266 NodeMcu 4M bytes Lua WIFI module”

Your email address will not be published. Required fields are marked *

You have to be logged in to be able to add photos to your review.

WeMos D1 mini – Mini NodeMcu 4M bytes Lua WIFI Internet of Things development board based ESP8266 by WeMos

Detials:

11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
   1 analog input(3.3V max input)
   a Micro USB connection
 
Package Included:
  1×WeMos D1 mini
   2×Long female pins
   2×Short female pins
   2×Normal pins