Synchronous Motor for Micro Crafts rotate exhibition Microwave oven 220-240V 4W 5-6RPM/min

SKU: 1107

In stock

PKR  470
Rated voltage:220-240V Frequency:50/60HZ Rated power:4W Rated speed:5~6R/Min Manner of working:CCW/CW

HC-06 HC06 HC 06 Bluetooth Serial 4 Pin Module

SKU: 1101

In stock

PKR  680
With VCC, GND, TXD, RXD foot for the bluetooth. With LED indicator light. 3.3V LDO baseboard. Input voltage 3.3-6V, the input voltage more than 7V is prohibited. Unpaired current is about 30mA, matched current is about 10mA.

10A10 10 Amp 1000V 10A 1KV Axial Rectifier Diode High Quality

SKU: 1098

In stock

PKR  15
10A10 10 Amp 1000V 10A 1KV Axial Rectifier Diode High quality

HC-09 Bluetooth Serial Module Compatible With HC-07 HC-06

SKU: 1076

In stock

PKR  800
Mainstream CSR Bluetooth chip, Bluetooth V2.0 protocol standards

2, serial module operating voltage 3.3V.

3, the baud rate can be set 2400,4800,9600,19200,38400,57600,115200,230400 user

4 core module size: 28mm x

4 Channel Relay Module Relay Expansion Board output 4-way outpu Relay

SKU: 1043

In stock

PKR  520
board four weeks with four screws holes, hole diameter 3.1mm, easy to install and fixed relay of high quality loose music relays SPDT. A common terminal, a normally open, one normally closed terminal optocoupler isolation, good anti-jamming low pull, high release. Energisation status indicator light, release status LED is off VCC of system power, JD_VCC relay power. You can plug in jumpers

2 CHANNEL 5v RELAY Module 2-channel

SKU: 1042

In stock

PKR  350
Relay contact capacity 250V10A. Relay output normally open, normally closed; • active low. 5V relay signal input voltage range :0-5V; • VCC system power. JD-VCC relay power. Default 5V relay. JD-VCC and VCC shorted

USB to TTL UART module CH340G CH340 3-3V-5V switch

SKU: 1014

In stock

PKR  250

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Status LED. Dual 3.3V and 5V Power output, work with 3.3v and 5v target device

UNO Proto shield prototype expansion board SYB-170 mini board

SKU: 1013

In stock

PKR  250
Used in conjunction with the Duemilanove ProtoShield prototype expansion board, the circuit is used to build a prototype, can be directly soldered components on the board, you can also connect the above mini breadboard circuit. Bread board and circuit board via double-sided adhesive connections, sold bread board and the circuit board are separated. ProtoShield prototype expansion board with two buttons and two LED circuit can be used directly, all of the pins and the power leads are very fit and build circuit prototyping with Ardui-no.

PL2303 USB To RS232 TTL USB Converter Adapter Module For Arduino

SKU: 1012

In stock

PKR  180

Adopt imported controller RS232 TTL,which can stabilize the flash with high speed
500mA self recovery fuse for protection
Two data transmission indicator can monitor data transfer status in real time
Reserve 3.3V and 5V pin interface,easy for the DDWRT of different voltage system that need power
The entire board is coated by high quality transparent heat-shrinkable sleeve,making the PCB in insulation state from outside,

LCD Display Module Blue Backlight for Arduino LCD1602 IIC I2C TWI 1602 Serial

SKU: 1011

In stock

PKR  1,050
It is another great blue backlight LCD display. As the pin resources of controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module,