Car Vehicle Bike Tools and Accessories
TP5000 4.2V/3.6V 1A Lithium Battery Charging Board Charger Module buy in Pakistan
PKR 160
In stock
کسٹمر کو رقم ادائیگی سے پہلے پارسل کھولنے کی اجازت ہے
| Weight | 0.003 kg |
|---|
On Sale Products
Related products
3S 25A Li-ion 18650 BMS PCM Battery Protection Board Balance Lipo Module
SKU:
1711
In stock
Over Charge voltage:4.25-4.35v±0.05v Over Discharge voltage: 2.3-3.0v±0.05v Max Working current:25A Max peak current:35-40A Working temperature:-40---+50 Storage Temperature:-40-- +80 Small current:50uA Life cycle:more then 30000 hours Resistance:Less than 100mΩ Short Cut : Protectable,Charge can repair
3S BMS 12V 100A Li-ion LMO protection lithium battery circuit board li-polymer balance
SKU:
2502
In stock
3S BMS 12V 100A Li-ion LMO protection lithium battery circuit board
li-polymer balance charging module
18650 battery charging module For lithium polymer protection board (3.7V)
Single cell battery overcharge protection voltage: 4.21-4.29V
Single cell battery overload protection recovery voltage: 4.14-4.24V
Overload protection delay: 1.5-2. 3S
Single cell battery over discharge protection voltage: 2.72-2.88V
Protection against current overload: 100 A
Over current protection: 100 A
Over discharge protection delay: 0.5-1. 3S
Temperature protect: Yes
Disconnect protect: Yes
Scarcity to protect: Yes
Shortage delay: 100-600 EE. USA
Scarcity Protection Recovery: Yes
Charging current: 60A
The current balance: Yes
Ampere (current): 60 mA
Voltage accuracy: 4.14-4.24V
3S 60A Protection Charging Board PCM BMS 18650 Li-ion Lithium Battery for Drill Motor
SKU:
2369
In stock
Charging voltage: 12.6V - 13.6V
Type:enhanced version,balanced version
Model: BMS-60A-3S
Item:Battery Charger Protection Board
Scope of application: Suitable for lithium batteries with nominal voltage of 3.7V and full voltage of 4.2V
(including 18650, 26650, polymer lithium batteries, no size limit).
Continuous discharge current (upper limit): 60A (If the heat dissipation environment is not good,
please reduce the load current)
Continuous charging current (upper limit): 15A
Enhanced version version: Suitable for electric drills with a starting current of 120A or less and a power of 260W or less.
Balance version: Suitable for electric drills with starting current below 120A and power below 260W, with balanced
charging function.
2S 8A 7.4V 8.4V Lithium LiPo Cell Li-ion BMS Battery 18650 Protection Board Tool
SKU:
2717
In stock
2S 8A 7.4V 8.4V Lithium LiPo Cell Li-ion BMS Battery 18650 Protection Board Tool
Model: HX2SD01
Over voltage range: 4.25-4.35v?0.05v
Over discharge voltage range: 2.5-3.0v?0.05v
Limited current: 15A
Upper working current: 8A
Quiescent current: less than 10uA
Operating temperature: -40 - +50?
Storage conditions: -40 - +80?
Resistance: less than 300m ohm
Short circuit protection: protection, charge recovery
Usage: 2 string 7.4V lithium Lipo Li-ion 18650 battery phosphate rechargeable battery pack.
Stable performance.
HW-370 TP5100 Single Double 18650 Lithium Battery Charging Board 2A Charger Module
SKU:
2969
In stock
TP5100 Single/Double 18650 Lithium Battery Charging Board 2A Charger Module
- Double 8.4v / 4.2v lithium rechargeable single
- Programmable charge current. 0. 1A-2A
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V
- Red and green LED charge status indicator
- Chip temperature protection, overcurrent protection, undervoltage protection
- Battery temperature protection, reverse battery shutdown, short circuit protection
- Switching frequency 400Khz, usable inductance 20uH and more
- PWR_ON Power battery for switching control
TP4056 5V 1A 18650 TYPE-C USB lithium Battery Charger Module Charging Board With Protection
SKU:
2963
In stock
TP4056 5V 1A 18650 TYPE-C USB lithium Battery Charger Module Charging Board With Protection
Input voltage: 4.35-6V (recommended voltage 5v)
Charge cut-off voltage: 4.2V +/- 1%
Maximum load current output: 1000 ma
Battery overcharge protection voltage: 4.28V
Battery Overcharge Boost Voltage: 4.00V
Battery discharge protection voltage: 3.0V
Battery discharge termination voltage: 3.2V
Battery: current 3A overcurrent protection
Board size: about 2.5 * 1.65CM
Indicator light: without charging the light not bright, the red light to recharge, it is full of green light.
HW-357 3.7V 9V 5V boost module and TP4056 Charging Module for 18650
SKU:
2594
In stock
1S 3.7V 3A LI-ION BMS PCM BATTERY PCB PROTECTION BOARD
SKU:
1864
In stock
10A 3s li-ion lithium battery 18650 12V BMS PCB protection board
SKU:
1825
In stock
1S 3A 3.7V Li-ion BMS PCM Protection Board for 18650 Lithium Lion Battery
SKU:
1814
In stock
Over charge voltage: 4.25±0.05V
Over charge release voltage:4.23±0.05V
Over discharge voltage:2.54±0.1V
Maximal continuous charging current: 2A
Maximal continuous Discharging current: 2A
Over current protection: 3A
The main function:
Overcharge protection, over discharge protection, short circuit protection, over current protection.
4S 30A Li-ion Lithium Battery 18650 charger protection board PCB
SKU:
1551
In stock
The protective board can be used as the nominal voltage of 14.4V, 14.8V, 16.8V four series of polymer lithium battery group, four series of 18650 lithium batteries as overcharge and over discharge, short circuit protection. Without the activation function in the power application for high instantaneous current,and in inverter application for avoid false triggering protection.So it will use more convenient.
Note:No part design on the back, can be attached to the heat sink to ensure high current work situation for a long time.
Power Bank Dual USB 5V 1A 2.1A 18650 Battery Charger PCB Accessories
SKU:
1122
In stock
Description
Product description:
TP5000 4.2V/3.6V 1A Lithium Battery Charging Board Charger Module
Description:
Features:Charging for Lithium battery(4.2V) and Lithium iron phosphate battery(3.6V)
Switch mode:
1. F Welding point ON for Lithium battery and output 4.2V
2. F Welding point OFF for Lithium iron phosphate battery and output 3.6V
8. Adjust output current(need to modify two resistance value on mark “SANYA”):
1. Default weld 1pcs R100(0.1ohm) resistor and output 1A(max)
2. Welding 1pcs 0.2ohm resistor next to R100 and output 1.5A(max)
3. Welding 1pcs 0.1ohm resistor next to R100 and output 2A(max)
4. Removed R100 and welding 1pcs 0.2ohm resistor on its place and output 0.5A
5. It requires additional heat sink if output current more than 1A.
Package Weight: 0.02kg (0.04lb.)
Package Size: 15cm x 12cm x 10cm (5.91in x 4.72in x 3.94in)
Specification:
Type:Voltage Regulator
Supply Voltage:DC 4.5-9V (not exceed 7V)
Model Number:TP5000 Lithium Battery Charger
Condition:New
Application:Electronic Circuit
Input voltage:DC 4.5-9V (not exceed 7V)
Output voltage:DC 4.2V/3.6V (default 4.2V)
Output current:1A (Default max)
LED Indicator:Charging -LED Flashing; Charged-Green
PCB size:21.5*14.5*4.2mm
Package includes:
1x TP5000 4.2V/3.6V 1A Lithium Battery Charging Board
Reviews (0)
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.