SW6206 SW6208 Qc4 Pd3.0 22.5w Power Bank Module

Features:

INTRODUCTION

SWITCH CHARGING

Current up to 5A, efficiency up to 95%

Support 4.2/4.35/4.4/4.5v battery type

Support for JEITA specification

Support temperature loop control
SYNCHRONOUS BOOST

Output power up to 22.5w, efficiency up to 95%
We Are The Distributor Of TZT Brand In Hong Kong, China
Automatic load detection / light load detection
Support wireless charging mode

Support small current mode

OUTPUT FAST CHARGING PROTOCOL
Support PPS /pd3.0 /pd2.0

Support qe4 + /qc4 / qc3.0 / qc2.0

Support AFC

Support FCP

Support FCP

Support SCP

Support pe2.0 /pet.1

Support SFCP

Support for vooc

INPUT FAST CHARGING PROTOCOL
Support pd3.0 /pd2.0

Support AFC

Support FCP

to be mobile phones, do not ask why, in short, can not be used in this way.
Need to charge mobile phones must be welded must be welded a lot of
buyers disobedient, whenever there is a problem, for example, my
motherboard how bad, motherboard can not quickly charge, motherboard
power off restart and so on, please operate in accordance with the
requirements, do not be self-righteous.)

4. 4.2V 18650 / polymer / ternary carp battery can be used in large monomer
or multi-section 18650 in parallel, but not iron battery, disposable dry battery,
Ni-MH, lead-acid battery, nickel pick battery and so on. The battery cannot be
connected in series. When the battery is powered on for the first time, the
display of the battery will be incorrect. please charge it again after discharge.
The first charge can continue to charge for more than 5 hours when the 4
lights are all on. There is no need to worry about it

5. Support OPPO flash charging and Huawei Super Fast charging. Different
protocols have different power. Understand clearly before shooting. This
scheme has been sold for a long time, except that some mobile phones do
not support fast charging. The reason for unsupported mobile phones is that
their own protocols are not made public and cannot be used by third parties,

so they can only be bought on the official websites of mobile phones.)

The charging process is divided inot the following three processes
Trickle mode, constant current mode and constant voltage mode.
When the battery voltage is lower than 3V, the charging module is in trickle mode and the
charging current is 300mA:
When the battery voltage is greater than 3V, the charging module will enter the constant
current mode. At this time, it will charge at full speed according to the set target current.
and the power can be about 21W:
When the battery voltage rises to the charging target voltage (such as 4.2V), the charging
module enters the constant voltage mode, and the current gradually decreases while the
battery terminal voltage remains unchanged;
When the charging current decreases to the cut-off current, the charging ends. After full
charge, if the battery voltage drops to 0.1V lower than the target voltage, it will automatically
restart charging.
(Note: if the voltage exceeds 4.2V, it is normal and the battery will not be damaged. When
the voltage is 4.2V, the light is still flashing, which means it is not fully charged. Full charge
depends not only on the charging voltage.)
There are five USB ports in the motherboard.
which are Type-A1 + Type-A2+ Micro-B + Type-C + Lightning,
Type-A1 and Type-A2 support QC3.0/QC2.0/AFC/FCP/SCP/PE2.0/PE1.1/SFCPNOOC
fast charging output;
Type-C supports PPS/PD3.0/PD2.0/QC4+/QC3.0/QC2.0/AFC/FCP/SCP/PE2.0/PE1.1/SFCP

Package:
1x SW6206 SW6208 Qc4 Pd3.0 22.5w Power Bank Module