Arduino &amp; Development Boards

SKU: 1928

In stock

PKR 1,100

Based on ESP32 WROOM-32 chip with dual-core processor (240 MHz)
Integrated WiFi 802.11 b/g/n and Bluetooth 4.2 (BLE)
38-pin breakout for full peripheral access
Supports SPI, I²C, UART, ADC, DAC, PWM, and touch sensing
Ultra-low-power operation for battery-powered projects
Works with Arduino IDE, Espressif SDK, and MicroPython
Perfect for IoT, automation, and robotics applications

Rain Sensor Water Detection Module for Arduino

Modules & Sensors

SKU: 1750

In stock

PKR 200

Connected to 5 v power supply, power indicator, no water droplets on induction plate, the DO output high level, switch indicator light out, drop a drop of water on, the DO output for the low level, the switch light is lit,Brush away the water droplets, again to return to, the output high level... AO analog output, which can be connected to the microcontroller AD mouth detection drops of rainfall in the above size. DO TTL digital output also can connect to the single chip microcomputer detect whether there is rain

ESP8266 NodeMcu Lua WIFI development board based on the CP2102

SKU: 1737

In stock

PKR 760

Chip Module: CP2102 Working Temperature: -40 ℃ ~ +125 ℃ Power Input: 4.5V ~ 9V (10VMAX), USB-powered Wi-Fi Module – ESP-12E module similar to ESP-12 module but with 6 extra GPIOs. USB – micro USB port for power, programming and debugging Headers – 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins Misc – Reset and Flash buttons Power – 5V via micro USB port Drive Type: Dual high-power H-bridge driver Current: continuous transmission ≈70mA (200mA MAX)

Mini 360 DC Buck Converter Step Down LM2596 Module 2A

Step Down (Buck) Modules

SKU: 1710

In stock

PKR 120

Rectification Methods: synchronous rectification Input Voltage: 4.75V-23V Output Voltage: 1.0V-17V Output Current: Peak 3A, long 1.8A Conversion Efficiency: 96% (the highest) Switching Frequency: 340KHz Output Ripple: 340mV (empty cut pm) Load Regulation: +/- 0.5% Voltage Regulation: +/- 2.5% Working Temperature: -40°C - + 85°C External Dimensions: 17 * 11 * 3.8mm (L * W * H)

Arduino Pro Mini 328 Mini ATMEGA328 5V/16MHz

SKU: 1347

In stock

PKR 600

Using Atmel Atmega328P - AU microcontroller digital input/output port RX and TX, D2 ~ D13, A0 ~ A5 8 analog input port A0 ~ A7 Support serial download 16 MHZ clock frequency

Step Down (Buck) Modules, Integrated Circuits

MP1584EN Ultra-small size DC-DC step-down module 3A

SKU: 1217

In stock

PKR 140

Name: DC-DC step-down module
Input Voltage: 4.5V ~ 28V
Output voltage: 0.8V ~ 20V
Output Current: 3A (Max)
Conversion efficiency: 96% (maximum)
Output Ripple: <30mV
Switching frequency: 1.5MHz (highest) typically 1MHz
Operating Temperature: -45°C ~ +85°C
Size: 22mm * 17mm (L * W )

150W DC-DC Boost Converter 10-32V to 12-35V 6A Step Up Voltage Charger Power

Step Up (Boost) Modules

SKU: 1188

In stock

PKR 500

Input voltage :10-32V Output voltage: 12-35V (adjustable) Output Current: 6A (MAX) Input Current: 10A (MAX) (Please enhance heat dissipation if more than 10A) Output power: natural cooling 100W (MAX), enhance heat dissipation 150W (MAX) Easy to drive 65W 90W dual-core notebook.

Power & Control Modules, Integrated Circuits

5V 9V 12V 10A PWM DC Motor Speed Controller LED Dimmer Module Adjustable Speed Regulator

SKU: 1180

In stock

PKR 280

Max voltage: 16V Minimum voltage: 5V Continuous current: 10A Short maximum current: 20A (less than 10 seconds) Speed control mode: PWM step-less speed regulation, can also be used to adjust the light Control mode: speed control potentiometer (clockwise clicked open, continue to rotate clockwise from 1% to 99% speed) Duty cycle: 0%-99% (0% position is the state of the switch off when the potentiometer is most on the left). When the current is switched on, the 0.002A (long time no need to switch off the governor is no current). Efficiency: the maximum efficiency is as high as 98%. Volume: long 3cm (excluding potentiometer), width 2cm, height 1.4cm

Step Down (Buck) Modules, Integrated Circuits

XL4015 DC-DC 5A Adjustable Step Down Module

SKU: 1178

In stock

PKR 230

DIY mobile power, car power, communications equipment and power supply. Technical Parameters: Module Properties: Non-isolated step-down module (BUCK) Rectification: Non-synchronous rectifier Input voltage: DC 5V-30V Output voltage: DC 0.8V-24V (Adjustable, Output < Input) Output current:Rated current is 2.5A,(5A Max, If current is larger than 2.5A, eEnhancement of heat dissipation is required.)

Step Up (Boost) Modules, Integrated Circuits

3V to 5V to 9V 2A USB Output Voltage Step-up Module Boost Converter

SKU: 1177

In stock

PKR 300

Input Voltage:2-6V(less than 3V,output power cut down)
Output Voltage:3.3V-9V adjustable(Input voltage must less than output voltage)
Output Current: Rated 2000mA (2.8V-3V input, 5V output, 1500MA output,(single lithium battery
higher 2600MAH input,5V output, output current can up to 2000MA)
Note: Output voltage higher than 6V, Please connect power first, then connect load line

Arduino UNO R3 SMD ATmega328P Board

SKU: 1138

In stock

PKR 950

Add two rows of the holes for the pins. So it can be connected with normal Dubond line. Add 3 rows of the holes for wiring. Change the in-line package of ATMEGA328P to flat package. CH340G Replace ATmega16U2

0.9V ~ 5V to 5V 600MA USB Output charger step up Power Module

Step Up (Boost) Modules

SKU: 1093

In stock

PKR 220

input voltage: 1-5V Output voltage: 5.1-5 .2 V Output Current: Rated 1A-1.5A (single lithium input), the maximum 1.5A (single lithium input) Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)