Click to enlarge
Home » Shop » TFT LCD 3.2 inch Mega Touch Expansion Board Shield for Arduino

TFT LCD 3.2 inch Mega Touch Expansion Board Shield for Arduino

PKR  1,350

In stock


Last updated: 12 March, 2024
x

کسٹمر کو رقم ادائیگی سے پہلے پارسل کھولنے کی اجازت ہے

SKU: 1400 Category:

TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board that use TFT01 LCD module.
TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist.

Related products

0.91 inch OLED display White 12832 IIC 128*32 LCD screen for arduino display device SSD1306

SKU: 1561

In stock

PKR  430
0.91 inch 128x32 I2C IIC Serial White OLED LCD Display Module 12832 SSD1306 LCD Screen Driver IC: SSD1306 Size: 0.91 inch OLED Resolution: 128 x 32 IIC interface Display Color: white
Add to wishlist
Add to cart
Quick view
-32%

12V DC voltmeter range 8 – 30V LED Digital Voltage Panel Meter

,
SKU: 1143

In stock

Original price was: PKR  280.Current price is: PKR  190.
Range: DC8-30V (No need aditional power) Display: Three 0.56'' LED digital tube Display color: red Refresh rate: about 500mS / times Input: DC voltage (<2 times the range) Resolution: 1% +1 digit
Add to wishlist
Add to cart
Quick view

Clear Acrylic Case Shell Housing For ESR SCR/MOS / LCR-T4 Transistor Tester

SKU: 1235

In stock

PKR  300
Description: 100% brand new and high quality Shape: Same as the picture show Clear Acrylic Housing : Suit For: LCR-T4 Transistor Tester Diode Triode Capacitance ESR Meter Note: It is DIY Parts, Not Assembled Package Included: 1 x Clear Housing Case
Add to wishlist
Add to cart
Quick view
DC 0V-100V Mini 0.28 inch Red LED Digital Voltmeter 3wire

DC 0V-100V Mini 0.28 inch Red LED Digital Voltmeter 3 wire

SKU: 1186

In stock

PKR  250

Specifications:

  • 2 line working voltage: 4.0~40V (with reverse connection protection function)
  • 2 wire detection voltage: 0.0~40V
  • 3 line working voltage: 4.0~40V (with reverse connection protection function)
  • 3 wire detection voltage: 0.0~100V
  • Operating current: <20mA
  • Display: 0.28, “LED”, red
  • Size: 33 x 10.7 x 8.2 mm (length * width * height)
  • Installing openings: 28.5 * 10 mm
  • The measurement rate: more than 200mS/ times
  • Measuring accuracy: 3 per thousand
  • Extreme working condition
  • Low operating voltage: +4.0V
  • Maximum operating voltage: +40V
  • Operating temperature: -10 ~ +65 DEG C
  • Working humidity: 10 ~ 80% (without gel)
  • Working pressure: 80 ~ 106 kPa
Add to wishlist
Add to cart
Quick view

DC 100V 50A Red Blue Digital Voltmeter Ammeter 2 in1 DC Volt Amp Meter With Shunt

, , ,
SKU: 1746

In stock

PKR  1,500
Operating voltage:DC 4 ~ 30V Measure voltage: DC 0 ~ 100V Minimum resolution(V): 0.1V Measure current :50A (require external shunt) Minimum resolution(A): 0.1A Operating current: <20mA Display: three 0.28" LED digital tube Display color: Red and Blue (two-color display) Refresh rate: about 300mS / times Measure accuracy: 1% (± 1 digit) Operating temperature: -10 to 65° c Operating Humidity: 10 to 80% (non-condensing) Working pressure: 80 to 106 kPa Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement
Add to wishlist
Add to cart
Quick view

Flysky FS-i6 FS I6 2.4G 6ch RC Transmitter with Receiver For RC Helicopter Plane Quadcopter Glider

SKU: 1304

In stock

PKR  19,500
RF specification: RF Range: 2.405 - 2.475GHz Bandwidth: 500khz RF Power: less than 20dBm RF mode: AFHDS 2A Modulation type: GFSK RX Sensibility: -105dBm Receiver specification: Channel: 6 Model type: fixed wing/helicopter/glider RF receiver sensitivity: -105dBm Modulation: GFSK System type: AFHDS2A/AFHDS Channel resolution: 1024 steps Bind port: yes Power port: yes( VCC) Power: 4V -6.5V DC Weight: 6.4g Antenna lenght: 26mm Size: 40.4 x 21.1 x 7.35 mm
Add to wishlist
Add to cart
Quick view

Square LED 8X8 Common Dots Matrix Module Arduino

SKU: 1025

In stock

PKR  450
LED Lattice Tube Matrix Module LED Display Dot Pin Numbers 16 Pins Total Size 60 x 60 X 7mm/ 2.4" x 2.4" x 0.28" (L*W*H) Material Plastic
Add to wishlist
Add to cart
Quick view

XD-82B 12V battery 4 section electricity indicator module board load E2V4

SKU: 1789

In stock

PKR  200
XD-82B 12V electricity indicator is a smart tool to indicate different levels of electircity. Section electricity indicator has 4 power indicator LED lamp, divided into 3 colors display, red, yellow, yellow, green represents 20%, 50%, 80%, 100 (%) of the electricity respectively.
Add to wishlist
Add to cart
Quick view
Description

Features:

  • TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board that use TFT01 LCD module.
  • TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist.
  • TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable
  • This LCD TFT01 Arduino Mega shield V2.2 is fit for 3.2 inch TFT LCD Module; The TFT01 MEGA shield supports 16-bit mode; Because of Mega board have enough pins for using SD card and touch function at the same time
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “TFT LCD 3.2 inch Mega Touch Expansion Board Shield for Arduino”

Your email address will not be published. Required fields are marked *

You have to be logged in to be able to add photos to your review.

Features:

  • TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board that use TFT01 LCD module.
  • TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist.
  • TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable
  • This LCD TFT01 Arduino Mega shield V2.2 is fit for 3.2 inch TFT LCD Module; The TFT01 MEGA shield supports 16-bit mode; Because of Mega board have enough pins for using SD card and touch function at the same time