6 in 1 Digital Current Voltmeter PZEM-022 AC 80V-260V 100A Split CT Power Multimeter

Product description:
PZEM-022 AC Digital Display Multimeter, Power Monitor, Voltmeter, Ammeter, Frequency Meter, Factor Meter
Product Type: PZEM-022
A Function
1. Electrical parameter measurement function (voltage, current, active power, energy, frequency, power factor)
2. Overload alarm function (over power alarm threshold, and power backlight intermittent to alarm ).
3. Power alarm threshold preset function (you can set the energy alarm threshold).
4. Power can be restored with the key.
5. Store data when turned off.
6. Large LCD screen
7. Backlight function.
B Key appearance and function
interface The display interface is large-screen LCD, it can display six parameters at the same time.
II screen format
1. Power: Test Range: 0 ~ 22000W, Startup Measuring Power: 0.5W
<10W Screen Format: 1.00 ~ 9.99W
<100W Screen Format: 10.0 ~ 99 , 9W
<1000W display format: 100 ~ 999W
< 10000W display format: 1.00 ~ 9.90kW ≥ 10000W display format: 10.0 ~ 22.0 kW
2. Power: Test range: 0 ~ 999kWh
<1kWh display format: 0 ~ 999Wh
<10kWh display format: 1.00 ~ 9.99kwh
≥ 10kWh display format: 10 ~ 999kWh
3. Voltage: test range: 80 ~ 260V
Display format : 80 ~ 260V
4. Current: test range: 0 ~ 100A, start measurement current: 0.02A
<10A display format: 0.000 ~ 9.000A
≥ 10A display format: 10.00 ~ 99.99A
5. Frequency: test range: 45 ~ 65Hz
Display format: 45 ~ 65Hz
6. power factor: Test range: 0 ~ 1PF
Display format: 0.00 ~ 1.00PF
III Key
1 control light
Briefly press the key to turn on or off the backlight, the backlight has memory function, it can store the
on or off status when power off.
2 reset power
Step 1: Press and hold the key for 5 seconds until the power value flashes, then release the key.
Step 2: Briefly press the key again, then the power value is cleared and exit the intermittent reset state.
Step 3: If there is no operation on the key within 5 seconds, it means the power value is not cleared
and will leave the reset state.
3. Set the power alarm threshold
Step 1: Press and hold the key until the LCD display shows “Set CLr”, then release the key to enter
the setting state
Step 2: Power window shows the value the current power alarm and the last digit starts flashing,
then you can briefly press plus 1, when it is not working for 3 seconds, it will change the digit position
automatically, the setting method is the same as above.
Step 3: After finishing setting, long press the key for 5 seconds will automatically store and exit, the active
power threshold range is 0.0 ~ 22kW.
C Precautions
1. This module is suitable for indoors, do not use outdoors.
2. The applied load must not exceed the nominal power.
3. The wiring order cannot be wrong.
D Specification of parameters
1. Operating voltage: 80 ~ 260VAC
2. Test voltage: 80 ~ 260VAC
3. Nominal power: 100 a / 22000 W
4. Operating frequency: 45-65Hz
5. Measurement precision: degree 1.0
Packing List:
1 * PZEM-022 AC Voltmeter Ammeter Multimeter
1 x open CT