Arduino Mega 2560 R3 CH340G/ATmega2560-16AU Micro USB With Bootloader
SKU:
2291
In stock
B3603 Step down DC-DC High Precision Charging 0-36V 0-3A
SKU:
1118
In stock
WeMos D1 Esp-Wroom-02 Motherboard ESP8266 Mini WiFi Nodemcu Module with 18650 Battery holder
SKU:
1965
In stock
One AD inputs.
Micro USB inputs.
One programmable LED (D0).
AUTO PROGRAM circuit.
ESP8266 (ESP-WROOM-02 With TELEC) is equivalent to the NodeMCU.
Analog Input (AD): Built-in dividing resistor (AD = 220K – ADC – 100K = GND).
There is a SOLDER terminal for SLEEP MODE.
Compatible With Arduino and NodeMCU.
Operation and charging are possible at the same time.
18650 charging circuit including the 5V boosting circuit with TP5410.
Overcharge protection, over-discharge protection built in.
LED: Red = Charging, Green = Full charging.
3000 mA 18650 It is possible to operate for more than 17 hours on a battery.
Integrated 18650 battery charging and discharging system.
One switch controls whether the 18650 battery is powered or not.
OLED’s SDA and SCL connected to the D1 pin and the D2 pin respectively.
The five buttons are controlled by FLATH, RSET, D5, D6, and D7 respectively.
The 5 Digital pins can configure the write/read/interrupt/PWM/I2C/one-wire supported separately.
Operation and NodeMCU consistent, adding a programmable LED, you can use GPIO16 to control, display 8266 running status and other functions. Integrated OLED and five buttons, more convenient for development.
The design concept originates from the open source project NodeMCU, and the development board integrates 18650 charging and discharging systems with charging and discharging protection. At the same time, an OLED and five directional buttons are integrated to facilitate the development.
HW-140 4A LCD Digital Display Step-up Step Down Module Buck Converter Voltage Regulator 5.5-30V
SKU:
2766
In stock
HW-140 LCD Digital Display Step-up Step Down Module Buck Converter Voltage Regulator 5.5-30V
Input Voltage: 5.5-30V (Input Voltage 5V, can also achieve step-up and step-down, but the
measurement of voltage and current is inaccurate; under-voltage protection below 4.7V)
Output voltage: 0.5-30V
Output Current: It can work stably in 3A for a long time and reach 4A under enhanced heat dissipation.
Output power: natural heat dissipation 35W, enhanced heat dissipation 50W
Voltage display resolution: 0.01V
Current Display Resolution: 0.002A
Soft Start: Yes (high power module with load may fail when starting)
Input Reverse Connection Protection: Yes
Output anti-backfilling: Yes
Short circuit protection: Yes
Working frequency: 180KHZ
LTC1871 DC-DC Step up Boost Module Power Supply 3.5V to 30V 100W LED Voltmeter
SKU:
2714
In stock
LTC1871 DC-DC Step up Boost Module Power Supply 3.5V to 30V 100W LED Voltmeter
1. Input voltage range :3.5-30V Note: 30V maximum voltage limit must be aggressive in order to
avoid accidental damage.
2. Output voltage range :3.5-30V (boost mode, the input must be less than or equal to the output voltage).
3. Input Current: 6A maximum 10A output power: 100W.
4. Note: According to the law of conservation of power output current under nominal conditions.
5. UIN * Iin * efficiency = Uout * Iout (UIN: input voltage Iin: input current).
6. Size: 66mm * 42mm * 18mm Weight: 35 g / pcs.
7. The voltmeter accuracy: ? (5 ? +1 word).
8. Static power consumption: Typical 15ma
(input voltage output voltage and the digital tube color is closely related to the actual current deviation).
9. IN +: Input the cathode IN-: Input negative OUT +: the output cathode OUT-: Negative output.
ECG Monitoring Sensor Module AD8232 Kit for Measuring Heart Pulse
SKU:
1780
In stock
The AD8232 is an integrated front-end for signal conditioning of cardiac bioelectrical signals for heart rate monitoring. This is a low-power, single-lead, heart rate monitor analog front end for a wide range of vital signs monitoring applications.
Technical Parameters:
Supply voltage: DC 3.3V
Output: Analog output
Interface (connected to RA LA RL): 3PIN 2.54 pin or headset
Size 36mm * 31mm * 18mm
Operating temperature: -40 'C - +85 'C
SIM800C Development Board GSM GPRS Module Support Message Bluetooth TTS DTMF Quad-band
SKU:
1738
In stock
Supports Bluetooth / TTS / DTMF function;
2. Reserve IPEX interface, SMA interface, spring antenna interface, it can be used for different occasions, different antennas;
3. Send reference program(please contact the servicer).
Product Features
1. Input voltage range 5V-20V DC, power supply range for a variety of power supply applications, it makes students and projects more convenient to use, GPRS module communicates in peak current, low voltage, so the higher the development board supply voltage, The smaller current makes the power supply pressure smaller, the integrated GPRS module to the product, the need to consider the development board of the power circuit, as far as possible making the width of more than 1mm power line, the shorter the better;
2. module connected to the power automatically after connected to the network, do not need to control the boot button, power directly to start, eliminating the need for trouble starting process, reserved boot pin, you can control the user switch;
3. TTL module with a level conversion circuit, compatible with a variety of single-chip serial port. Do not need to convert the direct connection;
4. Audio interface, pin-oriented way to facilitate the test, reverse headphones and microphone interface;
5. Bluetooth, Bluetooth 3.0 protocol, enhanced Bluetooth antenna signal super, support for serial SPP and audio services;
6. Reserve lithium battery-powered BAT interface, you can use the lithium battery-powered to facilitate the project development, 3.7V lithium battery or 18650 lithium battery;
7. Reserve IPEX interface, SMA interface, spring antenna interface, can be used for different occasions, different antennas.
XH-M452 THERMOSTAT TEMPERATURE AND HUMIDITY 12VDC HUMIDITY HYGROMETER CONTROLLER
SKU:
1958
In stock
XH-M602 CNC Lithium Battery LED Digital Tube Charging Control Switch Module Automatic Charger Protection Board 3.7
SKU:
3119
In stock
SOIC8 200mel Socket + SOIC8 Clip Adapter + CH341A USB Programmer
SKU:
2280
In stock
SOIC8 200milAdapter+SOIC8 Clip+EEPROM BIOS Writer CH341A USB Programmer
100% brand new and high quality
STC microcontroller supports a full range of program download
Provide 5V-3.3V power supply output
Support 25 SPI FLASH
For a variety of software for backup, erase, programming, calibration and other movements
Support USB to TTL
SOIC8 150mel Socket + SOIC8 Clip Adapter + CH341A USB Programmer
SKU:
2133
In stock
SOIC8 150milAdapter+SOIC8 Clip+EEPROM BIOS Writer CH341A USB Programmer
100% brand new and high quality
STC microcontroller supports a full range of program download
Provide 5V-3.3V power supply output
Support 25 SPI FLASH
For a variety of software for backup, erase, programming, calibration and other movements
Support USB to TTL
A multi-purpose machine, online Brush
LTC1871 Boost step up Module 100W With Dual Display Voltmeter
SKU:
1080
In stock